For: Design engineers and consultants specifying centrifugal pumps for water treatment, chemical, and power projects.
Why Selection Matters
Undersized: Insufficient flow or head → system cannot meet process requirements. Oversized: Pump runs in low-efficiency zone → energy waste, shortened equipment life, poor ROI.
Goal: Calculate flow, head, NPSH from operating data and select the right pump model.
I. Flow (Q) Determination
1. Definition and Units
Flow Rate: Volume of liquid pumped per unit time.
Common units:
- m³/h (cubic meters/hour): China, Europe.
- L/s (liters/second): Water treatment industry.
- GPM (gallons/minute): USA (1 m³/h ≈ 4.4 GPM).
2. Flow Calculation
Basic formula: Q = A × v
- Q: Flow (m³/h)
- A: Pipe cross-section (m²)
- v: Flow velocity (m/s)
Example: DN200 pipe (inner diameter ~0.2m), velocity 2 m/s → Flow = π × (0.1)² × 2 × 3600 = 226 m³/h.
Design flow determination:
- Process demand: Based on production line or consumption points (e.g., cooling water 50 m³/h for a reactor).
- Simultaneity factor: Not all points run at full load simultaneously → multiply by 0.7–0.9.
- Leakage allowance: Add 5–10%.
- Future expansion: If capacity may increase within 5 years, add 10–20%.
Design flow = Process flow × Simultaneity × (1 + Leakage) × (1 + Expansion)
3. Variable Flow Scenarios
If flow varies (valve throttling, intermittent use):
- Define normal, max, min flow.
- Select pump duty near normal flow (pump’s best efficiency zone).
- If max flow > duty × 1.2, consider larger pump or VFD control.
II. Head (H) Calculation
1. Definition
Head: Energy per unit weight of liquid the pump delivers, in meters (m).
Physical meaning: Lift height, or energy to overcome piping friction and pressure differences.
2. Head Calculation Formula
H = H_st + ΣH_f + ΔP / (ρg)
- H_st (static head): Elevation difference between suction and discharge liquid surfaces (m).; If pump below suction level (flooded), H_st may be negative or small.; If pump above suction level (lift), H_st = suction lift + discharge elevation.
- ΣH_f (friction losses): Suction and discharge piping friction + local losses (elbows, valves, tees).; Friction: H_f = λ × (L/D) × (v²/2g); λ: Friction factor (Moody chart or ~0.02–0.03); L: Pipe length (m); D: Pipe diameter (m); v: Velocity (m/s); g: 9.81 m/s²; Local: Each elbow ~0.5–1.0 m, gate valve fully open ~0.2 m, check valve ~2–5 m.
- ΔP / (ρg) (pressure head):; If discharge requires pressure (e.g., 0.3 MPa) → convert to head = 0.3 × 10⁶ / (1000 × 9.81) ≈ 30.6 m.
3. Head Calculation Example
Conditions:
- Suction level 0 m, pump 2 m, discharge level 20 m (open tank).
- Suction pipe DN150, length 5 m, 1 elbow.
- Discharge pipe DN150, length 50 m, 3 elbows, 1 gate valve, 1 check valve.
- Flow 100 m³/h, velocity v = 100 / (3600 × π × 0.075²) ≈ 1.57 m/s.
Calculation:
- Static head: H_st = 20 – 0 = 20 m (discharge level – suction level, pump elevation irrelevant).
- Suction losses:; Friction: 0.025 × (5 / 0.15) × (1.57² / 19.62) ≈ 0.05 m; Local (1 elbow): 0.5 m; Subtotal: 0.55 m
- Discharge losses:; Friction: 0.025 × (50 / 0.15) × (1.57² / 19.62) ≈ 1.05 m; Local (3 elbows + 1 gate + 1 check): 3 × 0.5 + 0.2 + 3 = 4.7 m; Subtotal: 5.75 m
- Total head: H = 20 + 0.55 + 5.75 = 26.3 m
- Pump selection: Choose duty head ~29–32 m (10–20% margin).
III. NPSH (Net Positive Suction Head) Check
1. Definition
NPSH: Suction condition required to prevent cavitation.
Two concepts:
- NPSHa (Available): Provided by the system, determined by layout.
- NPSHr (Required): Minimum needed by the pump to avoid cavitation, from pump curve.
Selection criterion: NPSHa > NPSHr + 0.5m (safety margin)
2. NPSHa Formula
NPSHa = (P_atm + P_s) / (ρg) – H_s – H_fs – P_v / (ρg)
- P_atm: Atmospheric pressure (standard 101.325 kPa = 10.33 m water).
- P_s: Suction tank pressure (0 for open tank; actual pressure for closed vessel).
- H_s: Pump centerline elevation above suction level (negative if below, positive if above).
- H_fs: Suction piping friction loss (m).
- P_v: Liquid vapor pressure at operating temperature (kPa, from tables).; 20°C water: 2.34 kPa ≈ 0.24 m; 60°C water: 19.9 kPa ≈ 2.0 m; 100°C water (boiling): 101.3 kPa ≈ 10.33 m
- ρ: Liquid density (water 1000 kg/m³).
- g: 9.81 m/s².
3. NPSH Example
Conditions:
- Open tank, liquid level 0 m, pump centerline 2 m (above level).
- Suction losses 0.5 m.
- Liquid temp 40°C, vapor pressure 7.4 kPa.
Calculation: NPSHa = 10.33 + 0 – 2 – 0.5 – 7.4 × 1000 / (1000 × 9.81) = 10.33 – 2 – 0.5 – 0.75 = 7.08 m
Selection: Check pump curve at 100 m³/h: NPSHr = 3.5 m. Verification: 7.08 > 3.5 + 0.5 = 4.0 m ✅ OK.
If NPSHa insufficient:
- Lower pump installation (closer to or below liquid level).
- Increase suction pipe diameter → reduce friction.
- Lower liquid temperature → reduce vapor pressure.
- Select lower-NPSHr pump (double suction, inducer).
IV. Efficiency and Power
1. Pump Efficiency (η)
Definition: Hydraulic power output / shaft power input.
Centrifugal pump efficiency ranges:
- Small pumps (< 10kW): 50–70%
- Medium pumps (10–100kW): 70–85%
- Large pumps (> 100kW): 80–90%
Selection tip: Choose operating point near BEP (Best Efficiency Point) on pump curve.
2. Motor Power (P)
Formula: P = ρ × g × Q × H × K / (3600 × 1000 × η) (kW)
- ρ: Density (kg/m³)
- g: 9.81 m/s²
- Q: Flow (m³/h)
- H: Head (m)
- η: Efficiency (decimal, e.g., 0.75)
- K: Motor safety factor (typically 1.1–1.2)
Example: Q = 100 m³/h, H = 30 m, η = 0.75, density 1000 kg/m³. P = 1000 × 9.81 × 100 × 30 × 1.15 / (3600 × 1000 × 0.75) ≈ 12.5 kW Motor: 15 kW (next standard size).
V. Selection Workflow Summary
- Determine duty: Flow, head, liquid properties (density, viscosity, temp, corrosivity), suction conditions.
- Calculate head and NPSH: Use formulas above, add 10–20% margin.
- Pre-select pump: Filter candidates by flow and head in catalogs or software (Grundfos Product Center, KSB EasySelect).
- Verify NPSH: NPSHa > NPSHr + 0.5m.
- Check efficiency: Operating point in high-efficiency zone (> 70%).
- Calculate motor power: Use formula, select next standard rating.
- Check materials and certifications: Match liquid corrosivity and project standards (CE, SASO, etc.).
Common Errors and Fixes
| Error | Consequence | Correct Action |
|---|---|---|
| Head = static only, ignore friction | Actual head insufficient, flow drops | Calculate friction and local losses |
| No NPSH check | Cavitation, vibration, noise, damage | Calculate NPSHa, ensure > NPSHr + 0.5m |
| Ignore efficiency curve | Low efficiency, high energy cost | Select near BEP |
| Excessive margin (e.g., head + 50%) | Wasted power, valve must be throttled | Keep margin 10–20% |
Summary: Right Selection = High Efficiency + Energy Savings
3 key points:
- Accurate flow and head: Include static, friction, pressure losses, with moderate margin.
- NPSH must be verified: Otherwise cavitation shortens pump life.
- Select in high-efficiency zone: Efficiency curve is key, not price alone.
If you are sourcing pumps, valves or related equipment for a project, send KFE your equipment list and operating data and we will help with selection and quotation.
Related industry: Chemical & Pharmaceutical




